This page has been translated automatically.
Programming
Fundamentals
Setting Up Development Environment
UnigineScript
High-Level Systems
C++
C#
UUSL (Unified UNIGINE Shader Language)
File Formats
Rebuilding the Engine and Tools
GUI
Double Precision Coordinates
API
Containers
Common Functionality
Controls-Related Classes
Engine-Related Classes
Filesystem Functionality
GUI-Related Classes
Math Functionality
Node-Related Classes
Networking Functionality
Pathfinding-Related Classes
Physics-Related Classes
Plugins-Related Classes
Rendering-Related Classes
Внимание! Эта версия документация УСТАРЕЛА, поскольку относится к более ранней версии SDK! Пожалуйста, переключитесь на самую актуальную документацию для последней версии SDK.
Внимание! Эта версия документации описывает устаревшую версию SDK, которая больше не поддерживается! Пожалуйста, обновитесь до последней версии SDK.

Port Angeles Setups

The Port Angeles demo can be run either in the single-channel or in the multi-channel mode.

To run the demo in the single channel mode, run one of the available launchers in the root of the Portangeles folder:

  • MS Windows:
    • portangeles_editor.bat – the demo with the loaded editor
    • portangeles_release.bat – the demo release version
  • Linux:
    • portangeles_editor.sh – the demo with the loaded editor
    • portangeles_release.sh – the demo release version

A multi-channel rendering mode is used to render the image in fragments by several computers (image generators) synchronized over the network in real-time.

The demo comes with the predefined setup for three screens in a row, which also can be used when there is only a remote access to computers. Instructions on custom setups can be found below.

Network Configuration:

  • Isolated physical network is required in order not to flood working environments with broadcast packets
  • Master and slaves computers should belong to the same subnet (default is 10.10.1.0)
  • The broadcast address should be set correctly (default is 10.10.1.255)
  • The bandwidth should be 1 Gbit/s
  • The firewall should be disabled or configured not to block the following TCP ports: 8880, 8801, 8800, 8890, 8891
  • Drivers for the network interface controller should be up to date
  • Default IP addresses:
    • 10.10.1.1 – the right slave
    • 10.10.1.2 – the center master/slave
    • 10.10.1.3 – the left slave

There are two ways of setting the master:

  • Master on IG
  • Master on dedicated PC

Master on IG Setup

  1. Open Portangeles/multi_channel/windows/ig_start_remote.bat (Portangeles/multi_channel/linux/ig_start_remote.sh) in the text editor and specify the following:
    • USER - the name of the user in the system
    • PASSWORD – the password (required)
    • DIRECTORY – the path to the project
  2. Run Portangeles/multi_channel/windows/ig_start_remote.bat (Portangeles/multi_channel/windows/ig_start_remote.bat). By running this script, parameters will be set automatically for each slave.
Notice
To kill main processes on each computer, use Portangeles/multi_channel/windows/ig_stop_all.bat (Portangeles/multi_channel/linux/ig_stop_all.sh) scripts.

Master on Dedicated PC Setup

  1. Open Portangeles/multi_channel/windows/ig_start_local.bat (Portangeles/multi_channel/linux/ig_start_local.sh) in the text editor and specify the following:
    • USER - the name of the user in the system
    • PASSWORD – the password (required)
    • DIRECTORY – the path to the project
  2. Run Portangeles/multi_channel/windows/ig_start_local.bat (Portangeles/multi_channel/linux/ig_start_local.sh. By running this script, parameters will be set automatically for each slave.
Notice
To kill main processes on each computer, use Portangeles/multi_channel/windows/ig_stop_all.bat (Portangeles/multi_channel/linux/ig_stop_all.sh) scripts.

Custom Setups

Recommendations:

  • Setup all of the slaves before the master
  • Do not forget to replace all of the default IP addresses if you are going to use your own addresses

Slave IG Custom Setup

  1. Open Portangeles/multi_channel/windows/run_slave.bat (Portangeles/multi_channel/linux/run_slave.sh) in the text editor.
  2. Specify the following slave options at the last line:
    • -slave_name - position in the monitor stack ( left, right, etc.)
    • -slave_grid_x - total amount of image generators positioned horizontally
    • -slave_view_x - the number of an image generator in the horizontal row
    • -slave_grid_y - total amount of image generators positioned vertically
    • -slave_view_y - the number of an image generator in the vertical row
    • DISPLAY – the number of the display, which can be obtained by the echo $DISPLAY command in the terminal (for Linux only)
  3. Run Portangeles/multi_channel/windows/run_slave.bat (Portangeles/multi_channel/linux/run_slave.sh).
    Notice
    For Linux you can specify display options both in the run_slave.sh file or pass them as keys on running in the following way: run_slave.sh name view_x display, where:
    • name – position in the monitor stack (left, right, etc.)
    • view_x – the number of an image generator in the horizontal row
    • display – the number of the display, which can be obtained by the echo $DISPLAY command in the terminal
    For example, run_slave.sh left 1 :0.
  4. Reiterate first three steps for each slave.

Master on IG Custom Setup

  1. Open Portangeles/multi_channel/windows/run_master_remote.bat (Portangeles/multi_channel/linux/run_master_remote.sh) in the text editor.
  2. Specify the slave options in the same way as described in the Slave IG Setupsection.
  3. Specify the master broadcast address at the last line:
    • -master_address - the current LAN segment broadcast address
  4. Run Portangeles/multi_channel/windows/run_master_remote.bat (Portangeles/multi_channel/linux/run_master_remote.sh).

The example below shows how to manually setup projections for three screen in a row using a Master on IG approach on Windows (each monitor is connected to a separate computer).

  1. Open Portangeles/multi_channel/windows/run_slave.bat in the text editor for two slave computers and specify the following at the last line:
    • For the first computer: -slave_name left -slave_grid_x 3 -slave_view_x 0
    • For the second computer: -slave_name center -slave_grid_x 3 -slave_view_x 1
  2. Open Portangeles/multi_channel/windows/run_master_remote.bat and specify the following at the last line:
    • -master_address 10.10.1.255 -slave_name right -slave_grid_x 3 -slave_view_x 2
  3. Run Portangeles/multi_channel/windows/run_slave.bat on each slave computer.
  4. Run Portangeles/multi_channel/windows/run_master_remote.bat.

Master on Dedicated PC Custom Setup

  1. Open Portangeles/multi_channel/windows/run_master_local.bat (Portangeles/multi_channel/linux/run_master_local.sh) in the text editor and specify the broadcast address at the last line:
    • -master_address – the current LAN segment broadcast address
Last update: 03.07.2017
Build: ()